BDS Suspension 2.5" Radius Arm Lift Kit 20-22 Ford SuperDuty F-450 4WD

Are you ready to gain some altitude in your F-450 SuperDuty coupled with increased suspension performance? Whether your truck stays on the pavement or you like to hit some dirt on the weekends, this kit from BDS will not only deliver additional ride height for larger tire fitment and ground clearance, but also a better ride, no matter the conditions. As far as quality...no cheap coil or radius arm spacers here, only fine tuned replacement coils and stout, stellar looking radius arms with this kit!At the heart of this system is a pair of heavy duty radius arms built to withstand whatever abuse you can throw at them. Built from 1-3/4" OD -10GA DOM tubing with support gussets, these replacement arms are far superior to the factory stamped steel units. They use a high clearance design for extra ground clearance and are formed inward to allow for additional clearance of oversized tires. They incorporate factory style 3-1/4" rubber bushings to minimize road vibrations and allow for a long, maintenance-free bushing life. The arms bolt into the factory mounting points and reposition the front axle to correct caster angle.The additional 2.5" of lift comes from a pair of full length diesel specific ProRide coil springs. These paired with your choice of NX2 Nitro series gas shocks or the precision tuned FOX 2.0 performance gas shocks offer a smooth ride and improved control over rough terrain. To improve steering angles a forged drop pitman arm is supplied with an integrated drag link flip. Used in combination with the heavy duty track bar that will position the front axle and keep the track bar angle in phase with the steering for improved handling. Also included for the front suspension are a pair of sway bar relocation brackets, bump stop extensions, and brake line relocation brackets. Out back a 1" fabricated block is used in place of the factory block to level the stance. Longer black e-coated u-bolts and your choice of NX2 or FOX 2.0 shocks round out this 2.5" radius arm lift system. Shock Option: FOX 2.0 Performance Series Shocks - Fox 2.0 performance series shocks have been tuned and tested by both FOX and BDS Suspension to maximize performance specific to each application and every BDS Suspension system. The Internal Floating Piston (IFP) shock design is based on proven Fox Racing Shocks race products but re-designed to maximize the ride quality, handling, and control of your BDS-equipped truck, whether on or off the road. Steering Stabilizer Options: Single NX2 Nitro: Are you worried about your steering control? NX2 Nitro Steering Stabilizer is designed to be a high-end performance shock at an affordable price. Built with a durable metallic finish, a large fluon-banded piston, and self-lubricating seals this stabilizer is tough enough to last but tuned with vehicle-specific valving to give you amazing control. Built with both the morning commute and some light off-roading in mind, keep stress out of your steer and install one of these today! Dual NX2 Nitro Series: Is one not enough? Then upgrade to a dual steering stabilizer setup which gives further enhanced vehicle control and lessens side-to-side motion to a greater effect. Heavy off-roading requires a heavy suspension that can handle it but can still be smooth on asphalt. Dual FOX 2.0 Performance Series: Taking things even further is the dual FOX 2.0 setup. Built to last from the top up this performance setup will enhance control, reduce shimmy and bump steer, and improve tire wear and front-end component life. Protect your investment and smooth out your rough spots before they leave you figuratively hanging. Recoil Traction Bar Kit Increase your traction and stability without limiting your movement with this BDS Recoil Traction Bar Kit. When your truck is in high torque situations, you need extra help absorbing shocks or vibrations through your system. Install these traction bars to smooth out your ride, increase stability while off-roading, and increase durability throughout your truck. Front Adjustable HD Track Bar These new track bars are a massive upgrade to the factory unit, constructed from 1-3/8? solid steel stock reinforced with gusseted ends to handle whatever on-road and off-road abuse you can through at it. Adjustments are made at the 1-3/8?-12 fine threaded center turnbuckle with pinchbolt ends to allow easy tuning to properly recenter the front axle for a range of lift heights. The track bar is formed for proper clearance around critical front end components and is designed to easy installation without the need to clearance the factory frame and axle mounts. Both ends use high-durometer polyurethane bushings with thick-walled steel sleeves for strength and reliability. Parts come with a high quality textured black powdercoat finish for a great look and excellent corrosion resistance. The are designed for use on 0-3" of lift and can be used in combination with most aftermarket track bar brackets to be used on taller lift heights.