The Unchained is a purpose built kit. 3.0" 2-Tube Front Kings and 4-Tube Bypass rear 3.0" shocks are paired with fabricated coil buckets, 4.5" lift multi-rate coil springs and Full Leafs in the rear for unsurpassed off-road capability from a bolt-on suspension system. A roll cage should be considered at this level of suspension.
If you're looking for the best on road ride offered by Carli with a huge boost in off-road capability, grab a Dominator. If you're after a suspension that will allow more off-road performance than the chassis to which it's bolted, this is your huckleberry. With the Unchained Suspension System, Carli recommends a roll cage and axle truss. This system is far more capable off-road than even the Coilover-Bypass System.
CARLI UNCHAINED SUSPENSION SYSTEM COMPONENTS
The truck will sit 4.5" higher in the front and have more wheel travel thanks to the taller, Progressive Rate Coil Springs that mount into the Fabricated Carli Spring Buckets. Radius Arm Drop Brackets reset the pivot point and keep the travel linear for the best ride while Sway Bar End Links reset the sway bar engagement point. The included Bump Stop Drops protect the shocks from over-compressing while the Adjustable Track Bar centers the front axle and Stainless Brake Lines firm up braking and ensure there is enough line for the newfound travel. To round off the front end, you'll also receive Caster Shims to tighten the steering.
SWAY BAR END LINK SPECIFICATIONS:- Corrects sway bar geometry on 4.5" lift
- Direct bolt-in
- Unhindered articulation, 100 percent rebuildable
- FK bearing 5/8" rod ends
REAR LEAF SPRING KIT
The rear is outfitted with a Full Progressive Spring Pack requiring no block to achieve proper ride height; thus, travel is extended and wheel hop/axle wrap minimized at the cost of 15% less load capacity than a stock F-250. If capacity is a concern, upgrade with Long Travel Airbags to restore the payload capacity to that of a SRW F-350.
FULL PROGRESSIVE LEAF SPRING KIT SPECIFICATIONS:- Block eliminating
- Light 3/4 ton capacity, full capacity attainable with long travel airbags
- Includes new u-bolts and rear bump stop drops
- Provides a 1" rear high stance on matching 4.5" suspension systems
- 3.5" axle tube
CARLI TUNED KING 3.0" SHOCKS
This system boasts Carli Signature tuned, King 3.0" 2-Tube Front and 4-Tube Rear Piggy-Back Bypass Shocks so large, Carli needed to fabricate custom mounts to fit them; as the old adage goes, there's no replacement for displacement. The 3.0" shock has a piston surface area 45% greater than a 2.5" King and 126% larger than a factory 2.0" shock making it far more efficient in all situations. Additionally, as explained above, they've added bypass tubes to this pinnacle off-road system. The massive surface area and bypass tubes ensure you'll achieve unmatched off-road performance while receiving a civil controlled on-road ride. To fit these shocks, included are fabricated mounts that lift the upper mounting point and position the shock away from the frame while the standard bump stop extensions were shortened to allow for more up-travel to compliment the additional down-travel from the longer shock.
In an effort to provide you with the best product, Carli designed a custom piston to determine proper base flow rates to ensure the shock works well in the heavy duty truck platform; the shocks were then tuned based on seat-of-the-pants feel. ALL of Carli's King shocks are rounded off with shafts machined and polished from a solid piece of 17-4 Stainless. Unlike King's standard shafts, there is no coating to wear off, weather is far less likely to hurt them and if there is a small chip, you can round the edges with emery cloth to ensure the seal housing isn't damaged as they're not brittle like the stock, hardened shafts. The shocks are finished with King oil good to -55° F. Note that all King shocks are built with a plated steel body. If subjected to inclement weather for extended periods, Carli recommends wrapping your shocks in 3M to provide a moisture barrier that's replaceable.
WHEEL AND TIRE FITMENT
As with the Coilover Bypass, it's recommended that users purchase a Differential Guard for axle protection, High Mount Steering Stabilizer to keep the steering as controlled as the suspension and Fabricated Radius Arms for strength and Limit Strap mounting. Again, at this level of suspension, a roll cage and axle truss is also recommended if the system will be used to its full off-road potential. On the 4.5" Bypass equipped Ford Systems, Carli recommends 17"-18" wheels, no more than 9" wide with 4.5"-5" of backspacing with a 37", E-Rated Tire. The more rubber, the better the small bump compliance will be at proper inflation pressures. The ride will firm up as you go larger in wheel diameter.
IMPORTANT NOTES:- WHEELS: Carli Recommends a 17"-18" Wheel, no more than 9" wide with 5" of Backspacing on 4.5" Lift Systems.
- TIRES: 37", E-Rated Tire Fitment is Recommended. Recommended unloaded Tire Pressure 45F/40R
- RECOMMENDED CONFIGURATION: Carli 4.5" Systems are Designed and Tested on Vehicles with 17"-18" Wheels with 37", E-Rated Tires. Stock wheels and tires or running a larger wheel diameter will result in a stiffer ride.
- REAR DRIVESHAFT Trucks equipped with a 2 piece driveshaft will require CS-CARRIERDROP-F to ensure proper driveline angles.
- Diesel Power Products and Carli strongly suggest the use of either options available. These options are designed to work flawlessly with the rest of your kit and, are the best way to go. However, we understand you may already have the necessary provisions and/or products to use with this kit so we give you the option to not include any leaf spring provisions.
- Diesel Power Products and Carli strongly suggest the use of either options available. These options are designed to work flawlessly with the rest of your kit and, are the best way to go. However, we understand you may already have the necessary provisions and/or products to use with this kit so we give you the option to not include any sway bar drop or Torsion Sway Bar provisions.
Specifications
- SkuCS-F45-UC30-08
- ManufacturerCarli Suspension
- MPNCS-F45-UC30-08
- Shock Diameter 3.0"
- Front Lift Height 4.5"
- Rear Lift Height on F-250 3.5"
- Rear Lift Height on F-350 2.0"
- Tire Size Up to 37"
- Front Travel 12"
- Rear Travel 12"
- Carli Tuned KING 3.0" 2-Tube Front Shocks
- Carli Tuned KING 3.5" 4-Tube Rear Bypass Shocks
- Stainless Steel Shock Shafts
- 4.5" Lift Multi-Rate Coil Springs
- Fabricated Coil Buckets
- Fabricated Rear Shock Mounts
- Brake Lines
- Radius Arm Drops
- Dominator Bump Stop Drops
- 1 Degree Caster Shims
- Adjustable Track Bar
- Sway Bar End Links
- Full Progressive Spring Pack
- Most Offroad Oriented Carli System
- Unsurpassed Control
- Unsurpassed Bottom Out
- Controlled On-Road Ride
NO VIDEOS AVAILABLE
Blog Posts
Recommended Products
Recently Viewed
Added To Cart
Carli 4.5" Unchained 3.0 Bypass Suspension System 08-10 Ford 6.4L Powerstroke
Quantity: 0
Cart Total$0000.00